- 您现在的位置：买卖IC网 > Sheet目录381 > 4306-00 (Peregrine Semiconductor)KIT EVAL FOR 4306 RF DSA
PE4306
Product Specification
Programming Options
Parallel/Serial Selection
Either a parallel or serial interface can be used to
control the PE4306. The P/S bit provides this
selection, with P/S = LOW selecting the parallel
interface and P/S = HIGH selecting the serial
interface.
Parallel / Direct Mode Interface
The parallel interface consists of five CMOS-
compatible control lines that select the desired
attenuation state, as shown in Table 5 .
The parallel interface timing requirements are
defined by Figure 18 (Parallel Interface Timing
Diagram), Table 9 (Parallel Interface AC
Characteristics), and switching speed ( Table 1 ).
For parallel programming the Latch Enable (LE)
should be held LOW while changing attenuation
state control values, then pulse LE HIGH to LOW
(per Figure 18 ) to latch new attenuation state into
device.
For direct programming, the Latch Enable (LE) line
should be pulled HIGH. Changing attenuation state
control values will change device state to new
attenuation. Direct Mode is ideal for manual control
of the device (using hardwire, switches, or jumpers).
Table 5. Truth Table
The LE input controls the latch. When LE is HIGH,
the latch is transparent and the contents of the serial
shift register control the attenuator. When LE is
brought LOW, data in the shift register is latched.
The shift register should be loaded while LE is held
LOW to prevent the attenuator value from changing
as data is entered. The LE input should then be
toggled HIGH and brought LOW again, latching the
new data. The stop bit (B0) of the data should
always be low to prevent an unknown state in the
device. The timing for this operation is defined by
Figure 17 (Serial Interface Timing Diagram) and
Table 8 (Serial Interface AC Characteristics).
Power-up Control Settings
The PE4306 always assumes a specifiable
attenuation setting on power-up. This feature exists
for both the Serial and Parallel modes of operation,
and allows a known attenuation state to be
established before an initial serial or parallel control
word is provided.
When the attenuator powers up in Serial mode
(P/S = 1), the five control bits and a stop bit are set
to whatever data is present on the five parallel data
inputs (C1 to C16). This allows any one of the 32
attenuation settings to be specified as the power-up
state.
When the attenuator powers up in Parallel mode (P/
S = 0) with LE = 0, the control bits are automatically
P/S
0
0
0
0
0
C16
0
0
0
0
0
C8
0
0
0
0
1
C4
0
0
0
1
0
C2
0
0
1
0
0
C1
0
1
0
0
0
Attenuation State
Reference Loss
1 dB
2 dB
4 dB
8 dB
set to one of four possible values. These four values
are selected by the two power-up control bits, PUP1
and PUP2, as shown in Table 6 (Power-Up Truth
Table, Parallel Mode).
Table 6. Power-Up Truth Table, Parallel
Interface Mode
0
0
1
1
0
1
0
1
0
1
0
1
16 dB
31 dB
P/S
0
LE
0
PUP2
0
PUP1
0
Attenuation State
Reference Loss
Note: Not all 32 possible combinations of C1-C16 are shown
Serial Interface
The PE4306’s serial interface is a 6-bit serial-in,
0
0
0
0
0
0
0
1
1
0
1
X
0
1
1
X
8 dB
16 dB
31 dB
Defined by C1-C16
parallel-out shift register buffered by a transparent
latch. The latch is controlled by three CMOS-
compatible signals: Data, Clock, and Latch Enable
(LE). The Data and Clock inputs allow data to be
serially entered into the shift register, a process that
is independent of the state of the LE input.
?2003-2013 Peregrine Semiconductor Corp. All rights reserved.
Note: Power up with LE = 1 provides normal parallel operation with C1-C16,
and PUP1 and PUP2 are not active.
Document No. DOC-30007-2 │ UltraCMOS ? RFIC Solutions
Page 6 of 11
Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
4307-00
KIT EVAL FOR 4307 RF DSA
4308-00
KIT EVAL FOR 4308 RF DSA
4309-00
KIT EVAL FOR 4309 RF DSA
4312-DK1
KIT DEV OOK RECEIVER SI4312
43A-015A
SENSOR PRES 15PSIA 0-100MV TO-8
450-0004
KIT DEV PROFLEX01-R2 F ANTENNA
450-0021
KIT DEV SIFLEX02 WIRE ANTENNA
450-0023
KIT DEV PROFLEX01 F ANTENNA
相关代理商/技术参数
430600-01-0
功能描述:TERM BARRIER 1CIRC SGL ROW .4375 RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:43000 标准包装:1 系列:43000 端接块类型:阻隔块 电路数:3 导线入口数目:3 间距:0.438"（11.12mm） 行数:1 电流:20A 电压:600V 线规:12-22 AWG 顶部端子:螺钉（不包括） 底部端子:快速连接（0.250"） 阻挡层类型:双壁（双） 特点:法兰 颜色:- 包装:散装 安装类型:底座安装或面板安装 工作温度:105°C 材料 - 绝缘体:聚丙烯（PP） 材料可燃性额定值:UL94 V-0
430600020
制造商:Curtis Industries 功能描述:Conn Barrier Strip 2 POS 11.11mm Wire Wrap ST Panel Mount 20A
430600-02-0
功能描述:TERM BARRIER 2CIRC SGL ROW .4375 RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:43000 标准包装:1 系列:43000 端接块类型:阻隔块 电路数:3 导线入口数目:3 间距:0.438"（11.12mm） 行数:1 电流:20A 电压:600V 线规:12-22 AWG 顶部端子:螺钉（不包括） 底部端子:快速连接（0.250"） 阻挡层类型:双壁（双） 特点:法兰 颜色:- 包装:散装 安装类型:底座安装或面板安装 工作温度:105°C 材料 - 绝缘体:聚丙烯（PP） 材料可燃性额定值:UL94 V-0
430600-03-0
功能描述:TERM BARRIER 3CIRC SGL ROW .4375 RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:43000 标准包装:1 系列:43000 端接块类型:阻隔块 电路数:5 导线入口数目:5 间距:0.438"（11.12mm） 行数:1 电流:20A 电压:600V 线规:12-22 AWG 顶部端子:螺钉 底部端子:焊接转塔 阻挡层类型:双壁（双） 特点:法兰 颜色:- 包装:散装 安装类型:通孔 工作温度:105°C 材料 - 绝缘体:聚丙烯（PP） 材料可燃性额定值:UL94 V-0
430600040
制造商:Curtis Industries 功能描述:Conn Barrier Strip 4 POS 11.11mm Wire Wrap ST Panel Mount 20A
430600-04-0
功能描述:TERM BARRIER 4CIRC SGL ROW .4375 RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:43000 标准包装:1 系列:43000 端接块类型:阻隔块 电路数:5 导线入口数目:5 间距:0.438"（11.12mm） 行数:1 电流:20A 电压:600V 线规:12-22 AWG 顶部端子:螺钉 底部端子:焊接转塔 阻挡层类型:双壁（双） 特点:法兰 颜色:- 包装:散装 安装类型:通孔 工作温度:105°C 材料 - 绝缘体:聚丙烯（PP） 材料可燃性额定值:UL94 V-0
430600-05-0
功能描述:TERM BARRIER 5CIRC SGL ROW .4375 RoHS:是 类别:连接器，互连式 >> 接线座 - 隔板块 系列:43000 标准包装:1 系列:OSTYK50 端接块类型:阻隔块 电路数:8 导线入口数目:8 间距:0.374"（9.50mm） 行数:1 电流:20A 电压:300V 线规:12-22 AWG 顶部端子:螺钉，带紧固板 底部端子:焊接转塔 阻挡层类型:双壁（双） 特点:法兰 颜色:黑 包装:散装 安装类型:通孔 工作温度:-40°C ~ 105°C 材料 - 绝缘体:聚酰胺（PA66），尼龙 6/6 材料可燃性额定值:UL94 V-0
430600060
制造商:Curtis Industries 功能描述:Conn Barrier Strip 6 POS 11.11mm Wire Wrap ST Panel Mount 20A